用户名: 密码:

生产装配车间常用英语

2008-08-28 09:11:03 作者:千岩 来源: 浏览次数:0 网友评论 0

About the dimension/关于尺寸bench ;base /基准点fiducial line /基准线base plane(plate)/ 基准面basic size; reference dimension/基准尺寸;oblique curse; slant /斜向   measure; gaging /测量parameter /参数d ...

About the dimension/关于尺寸
bench ;base /基准点
fiducial line /基准线
base plane(plate)/ 基准面
basic size; reference dimension/基准尺寸;
oblique curse; slant /斜向  
measure; gaging /测量
parameter /参数
division ,unit/单位
cross direction; lateral direction/ 横向
per unit length /单位长度
crosswise/ 斜地,成十字壮地,交叉地
center, core /中心
lengthwise direction ; longitudinal 纵向,经向,轴向
horizon ;level /水平.
up right; vertical ;perpendicular/垂直
radial component /径向部分
axial ; longitudinal /轴向
aperture size /孔径尺寸
pore size /孔径大小
radius; semidiameter /半径
diameter /直径,
circumference ; girth ;perimeter/周长
holes in pattern /排孔
pitch of holes in pattern /排孔节距
depth /深度
extent; length /长度
width; breadth /宽度
capacity ;cubic content/体积
square measure , area, dimension/面积
 
About the tolerance/关于公差
   configuration ;outline; contour/轮廓   error; blunder; inaccuracy /误差
tolerance ;allowance /公差 .      table of limits /公差表
tolerance  range (zone) /公差带   tolerance and fit /公差与配合
upper(down) variation of tolerance /上(下)偏差
hole tolerance /孔径公差         cylindricity ; roundness /圆柱度
form tolerances/形状公差         position tolerances/位置公差
circular degree /圆度 ,flatness;    planeness /平面度
parallelism tolerances/平行度.    verticality ; perpendicular/ 垂直度
bank error /倾斜误差             slant;  inclination pitch /倾斜度
axiality; concentricity /同轴度      symmetry /对称 
balanced; symmetric/对称的      positional tolerance zone /位置度公差带
surface roughness/表面粗糙度,    accuracy error /精度误差
required precision /精度要求      accuracy grade/ 精度等级
About the required technical(term)/ 关于技术要求
trimming; deburring /去毛刺      abate/倒钝  coping/修磨
reverse angle = chamfer/倒角   inclusion/杂质 allocation; fix position/定位
not up to standard/不合规格      to file burr /锉毛刺
poor staking/铆合不良           excesssive gap/间隙过大
grease/oil stains/油污            add lubricating oil/加润滑油
(be)qualfied, up to grade/合格    not up to grade, not qualified/不合格
to load a die/装上模具            to take apart a die/卸下模具
to tight a bolt/拧紧螺栓           to looser a bolt/拧松螺栓
to move away a die plate/移走模板    reset/复位 guide plate/定位板
dent/压痕   scratch/刮伤       deformation/变形  sliding block/滑块
location lump, locating piece, block stop /定位块     cam block/滑块
chassis / 基座  sprue /浇注口 leader pin /导柱outer guiding post/外导柱
inner guiding post/内导柱  dowel pin/固定销 located pin/定位销 pin/销
coil spring/弹簧wire spring/圆线弹簧inner hexagon screw/内六角螺钉
key groove(box; slot; gap; seat)/ 键槽   spline joint/(花)键槽连接
beam /横梁  channel /凹槽   lug /凸缘pit /坑  sinking /凹陷  Slot /槽
breaking.(be)broken,(be)cracked /断裂        slide rail(track) /滑轨
one stroke/一行程      top stop/上死点       bottom stop/下死点
incline; lean/倾斜    shrinkage hole /缩孔     outer bush外导套
assembly drawing/ 装配图   hatching /剖面线  coordinate/座标
finishing allowance /加工余量     factor/系数
       
easily damaged parts; fast moving /易损件       standard parts/标准件
sketch /草图   Overall dimension/ 轮廓尺寸   physical property/物理性能
mechanical character(property) /机械性能 elongation percentage /延伸率
Instrumented impact 机械冲击  shear strength/抗剪强度
Tensile strength/ 抗拉强度    Rigidity / 刚性     yield strength /屈服力
Tensile test /拉力测试  fatigue strength /疲劳应力  metallographical /金相
specific weight(density; gravity)/比重          oxidation /氧化
Appropriately designed corner 设计合理的拐角   eccentricity/偏心率

piece-production; single piece work/单件加工   L/N  Lot Number /批号
acceptance = receive/验收pre-fixed finishing date预定完成日
schedule; plan; rate of progress/进度
About the tool(device)/关于工具
pneumatic screw driver气动起子Screw driver起子
head of screwdriver起子头electric screw driver/  电动起子
glove(s)手套 band-aid创可贴 thumb大拇指 forefinger食指
little finger小指  mid finger中指ring finger无名指
fitter; bench work/钳工 fitter’s bench/钳工工作台
clamping fixture; holding device; jig /夹具 spline end wrenches/梅花扳手
lathe/车床 planer/刨床  miller/铣床 grinder/磨床    punch/冲床
sand paper /砂纸  tapping /攻螺丝  wrenches/扳手sockets/套筒
open End Wrenches/开口扳手       crowfoot Wrenches/块扳手   
hex Wrenches /内六角扳手  torque Wrenches/力矩扳手
pipe Wrenches /管钳      combination wrenches/开口/梅花扳手 
adjustable Wrenches/活动扳手  six Point Sockets/六角套筒 
twelve Point Sockets/梅花套筒  socket Extension/套筒接杆     
universal Sockets /万向套筒  adaptor/转接头universal Joint/万向转接头  
pliers/钳   bench clamp; vise /台钳  needle Nose Pliers/尖嘴钳 
locking Pliers/大力钳   convertible Snap Ring Pliers/卡环钳
eft fork/叉车 trolley/台车 jack/升降机 snip (scissor) /剪刀
depreciation 折旧

     
saw/锯   chisels/凿子   punch/錾子 tripod (spider) 三脚架   
copper hammer/铜榔头Iron hammer /铁榔头   rubber hammer/胶榔头
hook/弯勾    file/锉    pin Removal Tools/销钉插拔工具
pneumatic Runner/气枪  pneumatic Drills/气钻   rope/绳索   
tools Kit /工具箱   tools Rack/工具架 Jack /千斤顶    tommy Bar/撬棒  
work ladder/工作梯     grinding wheel/砂轮   sand paper/砂纸   
adhesive tape/胶带    driller/钻床 linear cutting/线切割
electrical sparkle/电火花 welder/电焊机 staker=reviting machine/铆合机
hydraulic machine/油压机common equipment/常用设备
About the measuring tool(device)/关于量具
bore gauge /孔径规thickness gauge/厚薄规cylinder square /圆筒直尺
feeler gauge /测隙规 gauge plate /量规定位板 height gauge /测高规
inside calipers/ 内卡钳 inside micrometer /内千分卡尺 dial snap gauge /卡规
depth gauge /测深规 caliper gauge/ 卡规 block gauge /块规
check gauge /校对规 clearance gauge /间隙规Outside Micrometer /螺旋卡尺
morse taper gauge /莫氏锥度量规 nonius /游标卡尺
square master /直角尺    steel Rulers/钢板尺   tape Rulers/卷尺
feeler (Thickness) Gauges/塞尺   dial Caliper/游标卡尺   stylus/ 触针
telescopic gauge /伸缩性量规 working gauge /工作量规 ring gauge/ 环规
protractor /分角器 passimeter /内径仪 position scale /位置刻度
About the warehouse/关于仓库
rack, shelf, stack/料架  to stock, storage, in stock库存
receive领取to retrn of goods退货raw materials原料
approved by / checked by / prepared by核准/审核/承办
hot rolled plate /热轧板  rolled angle;steelangle/角钢  structural section/型钢
specification/规格  material/材质  cold-drawn bar/冷轧棒料
hot rolled steel channel /热轧槽钢  hot-strip/热轧带钢

0
顶一下
0
踩一下

相关文章

[推荐] [收藏] [打印] [关闭] [返回顶部]

最新图片文章

最新文章